Plastic and metal belt

planning/designing

Optimization

Financial solutions

Maintenance

Practical training

Models

PA tp plastic belt conveyor

PA tp plastic belt conveyor

  • Sturdy structure in 6060 aluminium alloy section metal of primary extrusion protected by a 15-micron anodizing treatment
  • MB standard plastic belt without slats
  • Standard drive unit comprising a 0.18 kW three-phase asynchronous motor coupled to a permanently lubricated worm screw reduction unit. For safety reasons, the geared motor assembly is always equipped with a safety limiter
  • Fixed standard speed of conveyor 4 m/min
  • Standard voltage rating for the motors 400 Volts/50 Hz

Read more (PDF 25.2 MB)

CP tp plastic belt conveyor

CP tp plastic belt conveyor

 

  • Sturdy structure in 6060 aluminium alloy section metal of primary extrusion protected by a 15-micron anodizing treatment
  • MB standard plastic belt with slats h=35 mm, pitch=400 mm
  • Standard drive unit comprising a 0.18 kW three-phase asynchronous motor coupled to a permanently lubricated worm screw reduction unit. For safety reasons, the geared motor assembly is always equipped with a safety limiter
  • Fixed standard speed of conveyor 4 m/min
  • Standard voltage rating for the motors 400 Volts/50 Hz

Read more (PDF 25.2 MB)

CPT tp plastic belt conveyor

CPT tp plastic belt conveyor

  • Sturdy structure in 6060 aluminium alloy section metal of primary extrusion protected by a 15-micron anodizing treatment
  • MB standard plastic belt with slats h=35 mm, pitch=400 mm
  • Standard drive unit comprising a 0.18 kW three-phase asynchronous motor coupled to a permanently lubricated worm screw reduction unit. For safety reasons, the geared motor assembly is always equipped with a safety limiter
  • Fixed standard speed of conveyor 4 m/min
  • Standard voltage rating for the motors 400 Volts/50 Hz

Read more (PDF 25.2 MB)

PAR with plastic belt

PAR with plastic belt

  • The photo alongside shows a conveyor for collecting stacked plastic plates from the production unit outfeed and conveying these to the packaging unit
  • The two operating units have different work levels, therefore it is necessary to make the product “descend” to the level of the second unit
  • The plastic belt is functional to change in direction

Read more (PDF 25.2 MB)

Double conveyor with 90° bend with plastic belt

Double conveyor with 90° bend with plastic belt

  • The photo alongside shows a conveyor which completes a 90° bend without interrupting the continuity
  • Note the two different conveying lanes, each with its own adjustable polyzene side panels

Read more (PDF 25.2 MB)

Conveyor line with plastic belt

Conveyor line with plastic belt

  • The photo alongside shows a conveyor line from various product collection points to the collection centre
  • The peculiarity of the plastic belt used for these lines consists in the possibility of going through 90° bends without interrupting the continuity, thereby guaranteeting excellent quality conveying
  • Note the adjustable side panels with polyzene insert installed along the entire route
  • These lines are usually proposed for conveying small plastic containers

Read more (PDF 25.2 MB)

Linear conveyor with plastic belt and built-in 90° bend

Linear conveyor with plastic belt and built-in 90° bend

  • The photo alongside shows a conveyor line used in the packaging sector
  • In this application small plastic trays are conveyed to receive a metallic product deposited by the assembly line Robot
  • The photo also shows the line frame made of AISI 304 stainless steel
  • The slats comprising the belt are fitted with a skid-proof insert

Read more (PDF 25.2 MB)

PA tm metal belt conveyor

PA tm metal belt conveyor

  • Sturdy structure in 6060 aluminium alloy section metal of primary extrusion protected by a 15-micron anodizing treatment
  • MB metal belt without slats
  • Standard drive unit comprising a 0.37 kW three-phase asynchronous motor coupled to a permanently lubricated worm screw reduction unit. For safety reasons, the geared motor assembly is always equipped with a safety limiter
  • Fixed standard speed of conveyor 4 m/min

Read more (PDF 25.2 MB)

CP tp metal belt conveyor

CP tp metal belt conveyor

  • Sturdy structure in 6060 aluminium alloy section metal of primary extrusion protected by a 15-micron anodizing treatment
  • Standard MB metal belt with slats, h=20/30 mm, pitch 400 mm
  • Standard drive unit comprising a 0.37 kW three-phase asynchronous motor coupled to a permanently lubricated worm screw reduction unit. For safety reasons, the geared motor assembly is always equipped with a safety limiter
  • Fixed standard speed of conveyor 4 m/min

Read more (PDF 25.2 MB)

CPT tm metal belt conveyor

CPT tm metal belt conveyor

  • Sturdy structure in 6060 aluminium alloy section metal of primary extrusion protected by a 15-micron anodizing treatment
  • Standard MB metal belt with slats, h=20/30 mm, pitch 400 mm
  • Standard drive unit comprising a 0.37 kW three-phase asynchronous motor coupled to a permanently lubricated worm screw reduction unit. For safety reasons, the geared motor assembly is always equipped with a safety limiter
  • Fixed standard speed of conveyor 4 m/min
  • Standard voltage rating for the motors 400 Volts/50 Hz

Read more (PDF 25.2 MB)

PA conveyor with heavy-duty metal belt

PA conveyor with heavy-duty metal belt

The photo alongside shows a PA conveyor fitted with heavyduty metal belt used for conveying plastic or metallic material in heavy-duty environments, such as foundries, cutting, etc.

Read more (PDF 25.2 MB)

MB conveyor with heavy-duty metal belt

MB conveyor with heavy-duty metal belt

  • The photo alongside shows an MB tm conveyor fitted with heavy-duty metal belt
  • Note: the conveyor slats that have been welded to the belt
  • The structural framework of the conveyors on which the heavy-duty metal belt is fitted is made of 3mm thick sturdy welded painted sheet metal

Read more (PDF 25.2 MB)

EV elevator with heavy-duty metal belt

EV elevator with heavy-duty metal belt

  • The photo alongside shows an EV conveyor fitted with a heavy-duty metal belt used for lifting metallic products (screws, rivets, inserts, etc.)
  • The product is unloaded into a hopper and lifted according to the needs of the assembly line located downline
  • The hopper alongside is small but is available in larger size if necessary

Read more (PDF 25.2 MB)

System for receiving, conveying and separating products made of alloy

System for receiving, conveying and separating products made of alloy

  • The photo alongside shows a system consisting of an MB conveyor with metal belt complete with hopper in which the PVC connectors are deposited
  • The product is lifted and unloaded on a PA conveyor installed in the orthogonal position. This solution allows orthogonal alignment of the product
  • The height and pitch of the slats welded to the belt together with the conveyor speed determine a flow of connectors to be sent to the assembly unit by means of an orthogonal PA conveyor

Read more (PDF 25.2 MB)

CP conveyor with heavy-duty metal belt

CP conveyor with heavy-duty metal belt

  • The photo alongside shows an application widely used in various production sectors ranging from plastic materials, diecasting of products made of alloy, plastic material recovery sector, foundries for alloy and cast-iron, to carpentry
  • The lower flat section allows the installation of this conveyor inside the operating machine compartment where the unloading chute is present or in front of the conveyor provided in most production units
  • These conveyors are very sturdy and rarely require repair or maintenance

Read more (PDF 25.2 MB)

Separator with metallic rollers drum

Separator with metallic rollers drum

  • The photo alongside shows a version of the SR separator which we recommend for separating sprues/product made of zamak/alluminium or metallic material
  • This solution is widely used in the field of die-casting. The rollers comprising the drum are made of stainless steel tube, if necessary, or galvanized steel tube. In this solution, the rollers are fixed and don’t rotate around their own axis during the drum rotation
  • The distance between the rollers is adjusted manually
  • Note the insulation of the separator necessary for reducing noise to the minimum

Read more (PDF 25.2 MB)

Categories

Conveyors

 

 

Separators

 

 

Elevators

 

 

T50 Compact

 

 

Conveyors line

 

 

Cooling

 

 

Storage

 

 

Food and Pharma

 

 

Metal detector

 

 

Plastic and metal belt

 

 

PET solutions

 

 

Top control

 

 

Since 1985

MB Conveyors has more than 30 years of tradition and experience in mechanical industry and production of conveyor belts. The main qualities of the company are systemic functionality and profitability, commitment to clients, research and development with the support of experts.

Product quality is ensured through meticulous testing in all production steps along the line, with the use of most up-to-date production systems and materials of superior quality.

About the company and its products (PDF 25.2 MB)

Business lines

Automotive

medical

packaging

technical molding

teletronics

ENERGY EFFICIENCY

Energy efficiency is a concept that in our part of the world became important towards the end of 2008 and the beginning of 2009, at the outset of the world economic crisis. Most business people had, until then, mostly declaratively considered power consumption as a significant element of the total cost analysis. In these considerations, the impact of energy efficiency on the environment pollution had hardly been tackled at all.

Neofyton was among the first companies in Serbia and the region to start actively demonstrating the importance of energy efficiency, both by cutting production costs and therefore increasing profit rates and building awareness of the resource shortage and broader ecological principles.

Energy savings through the use of Neofyton's machines

In comparison with our direct competitors in the field of plastics injection machines, and with the utilization of standard hydraulics with integrated so-called "smart" pumps, our machines consume as much as 50% less energy. The use of servo-hydraulics opens up the potential of savings as high as 70%. We have a very precise power consumption measuring device to prove this.

The company Engel was the first plastics injection machine manufacturer back in 2009, which introduced the power consumption page as a standard component of the control assembly – "Ecograph", where - next to the weight of each product (molded part) in every cycle - total hourly consumption is shown, as well as the specific power consumption per one kilogram of processed plastics (kWh/kg).

ENVIRONMENTAL PROTECTION

The equipment we represent contributes to ENVIRONMENT PROTECTION in several ways.
When it comes to ancillary equipment, above all water chillers by our supplier Eurochille, used for temperature control of both hydraulics and machine servo motors and molds (tools) in which finished products are made, the chiller systems we sell facilitate the use of a new cooling system based on the so-called "adiabatic effect".

In summer, the hydraulics and servo motors of the injection molding machines call for cooling with water at a maximum of 28°C. Using the so-called "free cooling" device with the "adiabatic effect", cooling of process water is performed without cooling compressors (which use freon as the heat exchanger). Heat exchange, i.e. cooling happens exclusively by the use of ventilators, which translates into six- to eightfold savings compared to traditional chillers that use freon-based compressors.

One of our customers has reduced the required cooling energy by 1.400.000 kWh per year, i.e. by about 70.000 EUR, using the "adiabatic" cooling devices. An additional benefit is the elimination of major pollution risks which might arise from emissions of freon into the atmosphere due to tube puncture or breakage.

A similar calculation can be applied to our Engel injection molding machines, as well as to the Piovan granulate dryers.

Neofyton – partner of MB Conveyors

Neofyton is MB Conveyors’ partner for the markets of Serbia, Bosnia and Herzegovina, Macedonia, Nigeria, and Cameroon.

FSRV PLUS independent spiral roller separator – a new generation separator, designed to improve performances of the traditional spiral roller and to achieve particularly precise and efficient separation of the product from the sprue.

Neofyton youtube chanel

Neofyton provides “turnkey” solutions

From system design to machine installation and training

Neofyton partners

Proud members

Contact us

3 + 15 =